Creative 0404 Owner's Manual Page 9
- Page / 94
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2 - Installation
Setting Up the Digital Audio System
E-MU Digital Audio System 1
2 - Installation
Setting Up the Digital Audio System
There are five basic steps to installing your E-MU system:
1.
Install the E-MU 0404 PCI card in your computer. Go there.
2.
Install the optional Sync Card (if you have one). Go there.
3.
Attach the Analog and Digital breakout cables to the rear of the 0404 card.
4.
Install the PatchMix DSP software onto your computer.
5.
Connect audio, MIDI and synchronization cables between the Digital Audio System
and your other gear.
Please read the following sections as they apply to your system as you install the E-MU
0404, paying special attention to the various warnings they include.
Prior to installing the hardware, take a few moments to enter the serial number of the
E-MU 0404 PCI Card. These numbers can help EMU Customer Service troubleshoot any
problems you may encounter—by writing the numbers down now, you’ll avoid having
to open your computer to find them later on.
Safety First!
As you install
hardware components,
observe the following
general precautions to
avoid damage to your
equipment and yourself.
• To avoid possible permanent damage to your hardware, make sure that all
connections are made to the E-MU 0404 PCI card with the host computer’s power
off.
Unplug the computer’s power cable to make sure that the
computer is not in sleep mode
.
• Take care to avoid static damage to any components of your system. Internal
computer surfaces, the E-MU 0404 PCI board and the interfaces are susceptible to
electrostatic discharge, commonly known as “static.” Electrostatic discharge can
damage or destroy electronic devices. Follow these procedures when handling
electronic devices in order to minimize the possibility of causing electrostatic
damage:
• Avoid any unnecessary movement, such as scuffing your feet when handling
electronic devices, since most movement can generate additional charges of static
electricity.
• Minimize the handling of the PCI card. Keep it in its static-free package until needed.
Transport or store the board only in its protective package.
• When handling a PCI card, avoid touching its connector pins. Try to handle the
board by its edges only.
• Before installing a PCI card into your computer, you should be grounded. Use a
ground strap to discharge any static electric charge built up on your body. The
ground strap attaches to your wrist and any unpainted metal surface within your
computer.
If you don’t have a ground strap, you can ground yourself by touching the metal
case of another piece of grounded equipment.
• Before connecting a cable to your interface or between PCI cards, touch the
connector sleeve of the cable to the sleeve of the jack to which you’ll be connecting
the cable in order to discharge any static build-up.
- Owner's Manual 1
- Digital Audio System 1
- Owner’s Manual 2
- Table of Contents 3
- Creative Professional v 5
- 1- Introduction 7
- Notes, Tips and Warnings 8
- 2 - Installation 9
- Connector Types 10
- Install the Sync Card 11
- Software Installation 12
- 3 - PCI Card & Interfaces 13
- Analog Input Connections 14
- Using MIDI Thru 15
- The Sync Daughter Card Option 16
- 4 - The PatchMix DSP Mixer 17
- Mixer Window 18
- Mixer Block Diagram 18
- The Toolbar 19
- The Session 20
- Open Session 21
- Save Session 21
- Session Settings 21
- Using External Clock 22
- I/O Settings 22
- Input Mixer Strips 23
- Mixer Strip Creation 24
- Insert Section 25
- The Insert Menu 26
- E-MU Digital Audio System 19 27
- Meter Inserts 28
- Consumer 29
- Professional 29
- Trim Pot Insert 30
- Main / Monitor Bus 31
- Pre-Fader Aux Send 32
- Post-Fader Aux Send 32
- Main Section 34
- TV Screen & Selectors 35
- Main Bus 37
- Output Section 38
- 5 - Effects 39
- FX Insert Chains 40
- To Delete an FX Category 41
- To Rename an FX Category 41
- FX Edit Screen 42
- User Preset Section 43
- 96kHz Operation 44
- Core Effects Descriptions 45
- Frequency 46
- Low Shelf Mid Band High Shel 46
- 4-Band EQ 47
- Auto-Wah 48
- Signal path = Stereo 49
- Basic Controls 50
- Feedback 52
- Freq Shifter 53
- Leveling Amp 54
- Mono Delay 100 54
- Mono Delay 3000 55
- Phase Shifter 56
- Speaker Simulator 57
- Stereo Delay 100 57
- Stereo Delay 1500 58
- Stereo Reverb 59
- Early Reflections 59
- Late Reverb 59
- Vocal Morpher 60
- Phoneme A 60
- Phoneme B 60
- 6 - Working with ASIO 61
- Basic Recording 63
- Select the Audio Files Folder 64
- Set up your Inputs to Record 65
- The Cubasis Demo Song Screen 65
- Record a Track 66
- Record Another Track 66
- Direct Monitoring 67
- (recording) 68
- (playback) 68
- (back to PatchMIx DSP) 69
- Connection Setups 70
- Outboard Signal Processor 71
- E-MU VST E-Wire 72
- E-Delay Compensator 73
- PatchMix 74
- 7 - Appendix 77
- SMPTE Modes of Operation 78
- SMPTE Background 79
- Why use SMPTE? 80
- Striping SMPTE 80
- Avoiding SMPTE problems 80
- MIDI Time Code (MTC) 81
- Word Clock In/Out 81
- SYNC CARD 83
- DIGITAL BREAKOUT CABLE 83
- Digital Mixer 83
- ADAT Optical 83
- Useful Information 84
- Technical Specifications 85
- Dimensions & Weight 86
- Internet References 87
- Declaration of Conformity 88
- Compliance Information 89
- 82 Creative Professional 90
- Numerics 91
- E-MU Digital Audio System 83 91
- 84 Creative Professional 92
- E-MU Digital Audio System 85 93
- 86 Creative Professional 94
Related products and manuals for Soundbar speakers Creative 0404
(18 pages)
(10 pages)
(21 pages)
(2 pages)
Soundbar speakers Creative 510D User Manual
(22 pages)
(22 pages)
© 2020, manymanuals.com. All rights reserved. | 1.719 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals