Creative 3D Blaster User's Guide download pdf (Page 5)

Safety & Regulatory Information

The following sections contain notices for various countries:

Safety Information

CAUTION: This device is intended to be installed by the user in

a CSA/TUV/UL certified/listed IBM AT or compatible personal

computers in the manufacturer’s defined operator access area.

Check the equipment operating/installation manual and/or with

the equipment manufacturer to verify/confirm if your equipment

is suitable for user-installed application cards.

ATTENTION: Ce carte est destiné à être installé par

l’utilisateur, dans un ordinateur compatible certifié

CSA/TUV/UL ou listé IBM AT, à l’intérieur de la zone définie

par le fabricant. Consulter le mode d’emploi ou le fabricant de

l’appareil pour vérifier ou confirmer si l’utilisateur peut y

installer lui-même des cartes périphériques.

Notice for the USA

FCC Part 15: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference

to radio communications. However, this notice is not a guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try one or more of the following

measures:

! Reorient or relocate the receiving antenna.

! Increase the distance between the equipment and receiver.

! Connect the equipment to an outlet on a circuit different

from that to which the receiver is connected.

! Consult the dealer or an experienced radio/TV technician.

CAUTION: To comply with the limits for the Class B digital

device, pursuant to Part 15 of the FCC Rules, this device must be

installed in computer equipment certified to comply with the

Class B limits.

All cables used to connect the computer and peripherals must be

shielded and grounded. Operation with non-certified computers

or non-shielded cables may result in interference to radio or

television reception.

Modifications

Any changes or modifications not expressly approved by the

grantee of this device could void the user’s authority to operate

the device.

Notice for Canada

This apparatus complies with the Class “B” limits for radio

interference as specified in the Canadian Department of

Communications Radio Interference Regulations.

Cet appareil est conforme aux normes de CLASSE “B”

d’interference radio tel que spe’cifie’ par le Ministère Canadien

des Communications dans les règlements d’interfe’rence radio.

Compliance

This product conforms to the following Council Directive:

! Directive 89/336/EEC, 92/31/EEC (EMC)

Declaration of Conformity

According to the FCC96 208 and ET95-19 documents,

Name: Creative Labs Inc.

Address: 1901 McCarthy Boulevard

Milpitas, CA. 95035

United States

Tel: (408) 428-6600

declares under its sole responsibility that the product

Trade Name:Creative Labs

Model Number:CT6760

as been tested according to the FCC / CISPR22/85 requirements

or Class B devices and found compliant with the following

standards:

EMI/EMC: ANSI C63.4 1992, FCC Part 15 Subpart B

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received,

including interference that may cause undesirable

operation.

Ce matériel est conforme à la section 15 des régles FCC.

Son Fonctionnement est soumis aux deux conditions

suivantes:

1. Le matériel ne peut étre source D’interférences et

2. Doit accepter toutes les interférences reques, Y

compris celles pouvant provoquer un fonctionnement

indésirable.

Supplementary Information:

CT6760 is PCI interface

Compliance Manager

Creative Labs, Inc.

13 August 1998

1 2 3 4 5 6 7 8 9 10 ... 53 54

Comments to this Manuals

No comments

Creative 3D Blaster User's Guide Page 5

Comments to this Manuals

Related products and manuals for Graphics cards Creative 3D Blaster